![fender champ lap steel serial numbers fender champ lap steel serial numbers](https://www.retrofret.com/images/8574_Guitar/xLarge/8574_02.jpg)
![fender champ lap steel serial numbers fender champ lap steel serial numbers](https://vintageelectric.com.au/wp-content/uploads/2019/11/1954-Fender-Champion-Small-Sold.png)
Interestingly, these pots used more than one dating system, sometimes using numerals in the format WWY (typically early 1960s), and sometimes, a letter-based format, similar to the Egen codes above. Although they do not have an EIA manufacturer code, they are quite distinctive - small (about 3/4" diameter), with a brown plastic back with Morganite in raised lettering. Morganite pots were commonly fitted to British Vox guitars.
#FENDER CHAMP LAP STEEL SERIAL NUMBERS CODE#
So an Egen date code of 'JK' means October 1963 (J = October, K= 1963). The year code may not encompass the entire alphabet (then again it may), but the most relevant section covering British guitar construction (early-mid 1960s) ran H-O (1960-1967). Egen potentiometers have a simple two letter date code in the format MY (although occasionally they used YM). They do not use an EIA code, but are easily identifiable, typically having EGEN stamped onto the top of the pot (next to the shaft) and a tape covering the data on the side of the pot. EgenĮgen Electric Limited were a British electronics supplier whose pots were widely used in guitars by Vox, Fenton Weill, Hohner and others. These are some of the simplest codes to read, and it is therefore unsurprising that this system has become standard. For example 1346120 is a Centralab pot (134) produced in the 20th week of 1961. These often run on from the manufacturer code. CTS, Centralab, Stackpoleĭate codes were usually in three or four digits, one or two digits giving the year (for many US pots one digit refers to the 1950s, two digits to the 1960s), and two giving the week of the year. Sometimes these are simple, sometimes exceptionally complicated (for no useful reason!). Other companies from around the world used different systems using letters to denote differing years and months.
![fender champ lap steel serial numbers fender champ lap steel serial numbers](https://sc1.musik-produktiv.com/pic-010122772_05xxl/fender-70th-anniversary-esquire-sfg.jpg)
Each company had it's own dating system, although there was some consensus, particularly in American parts. Production dates regularly appear on potentiometers, though usually encoded to some extent. Other worldwide manufacturers just used the company name rather than a code. Although many others were used, these are by far the most important, as they were widely used by the likes of Gibson, Fender, Guild and Epiphone. American pot manufacturers had their own numerical EIA (Electronic Industries Alliance) codes, for example 134 = Centralab, 137 = CTS and 304 = Stackpole. There are very many electronic companies worldwide producing potentiometers, but most American vintage guitars of the 20th Century used pots by just a few manufacturers. You can look up Gibson potentiometers by their part number in the Gibson pot index on this site. Many pots do not have part numbers, but the larger guitar manufacturers did list pots by part number in their spare parts manuals. But read on, dating a vintage guitar with pot codes is sometimes more reliable than dating with serial numbers! Part numbers There are many exceptions and variations to the general rules described below, some of which are highlighted in the examples at the end. Finding them is not always easy this is obviously not something for the faint-hearted, but once performed a few times, nowhere near as daunting as it might at first seem. Codes can be worn, obscured by solder and other components, or simply very small. So reading them will require opening control cavities, removing scratchplates, or in the case of a semi acoustic, removing the pots entirely. So where are these codes? Normally they are stamped or inked onto the back or sides of the pot. Many pots don't carry all of this information, but the better quality guitars produced in America regularly do. Better quality pots are often stamped with a number of codes typically part numbers, date of production, manufacturers codes and resistance values.
#FENDER CHAMP LAP STEEL SERIAL NUMBERS FULL#
The pots, or potentiometers to give their full name, are the variable resistors that control volume and tone. If you've been reading articles about dating a vintage guitar, you may well have come across mention of pot codes, and the concept of using pot codes to date your guitar. Once decoded, the writing on the back or sides can be very informative in dating your guitar